Visi Timer

Important Safety Instructions

CAUTION! OPENING THE DEVICE MIGHT RESULT IN ELECTRICAL SHOCK

Visually check the product for any signs of damage, component failure and/or missing parts.

Do not distract others while they
are installing the product.

Any changes or modifications to the devices hardware or software will void the warranty of the device and may cause the device not to work properly.

The trampoline and its surroundings must always comply with local standards for trampolines.  

If the instructions contradict the local regulations please disregard them.

Keep the device away from any contact with water. Warranty void after water damage.

For indoor use only.

Keep the device away from fire. Warranty void after fire damage.

Installation should be performed by
authorized personnel.

Be sure to take all anti-static
precautions.

Optimum operating temperature
is from 5°C to 30°C. Avoid extreme
fluctuations of temperature.

Wear appropriate clothing: Do not
wear loose clothing or jewellery.

These instructions apply to the
device itself. Please read the manual
before operation.

Long hair should be tied back.
Tidy back any loose cables that could become a tripping hazard.
Immediately inform Visior games
for maintenance advice if you have
concerns.		 Always use designated buttons on the designated system. and/or missing parts.

 

What’s in the box?

Full setup

First time setup

A typical installation should take 2 people around 60 minutes.

Ensure there is nobody on the trampoline when installing the device. Make sure that the buttons are correctly oriented and clear of any obstructions.

Provide 230V 5A for the device.

 The buttons are pre assigned to the computer that came with the game set, you can’t switch them with other systems. Be careful when installing, buttons are clearly labeled to which side they belong to.
Provide internet connection point. All of the Visiorgames products need to connect to the internet. If you own more than one device, provide internet access to the device in the center of the park and connect the devices via router or hub.  Make sure the electrical power is off during installation.

Installation checklist

CHECK 1 Pre-power up checkups

  • Mounted onto a cushion designed for the game.
  • All buttons are connected to separate aggregator boxes.
  • All buttons are on the correct side.
  • Start buttons on the beginning and stop button in the end of the course.
  • There are two cables connected from aggregator boxes to the computer and connectors tighten.
  • Make sure the ethernet cable with internet access is connected to the computer.
  • Make sure the display and computer are connected with HDMI.
  • All fixings are tight and secure.
  • No signs of damage, component failure and/or missing parts.
  • No trapped and/or pinched cables.
  • No loose cables that could become a tripping hazard.
  • Make sure there is no strain on the cables and the connectors.
  • All electrical components are away from contact with water and heat sources.

CHECK 2 Power up

  • All buttons light up for a brief moment.
  • The display is turning on.
  • Game start screen appears on the display after around 1 minute.
  • Go! sound is heard at startup.
  • All buttons light up before the start of the game.

CHECK 3 Game running

  • Press the 1GO button and check the timer if it’s correctly assigned for player 1. repeat for 2GO, 3GO and 4GO.
  • Press the 1STOP button and check the display, the timer must stop. Repeat for 2STOP, 3STOP and 4STOP buttons.

CHECK 4 Ready for use

  • Play area is clear of any obstructions.

 

Powering on for the first time

  Make sure that all cables are connected to
the aggregator boxes and the computer and
connectors tightened.		   Monitor must power on by itself when
connected to power.
 

Make sure that the targets are on the correct side of

court relative to the monitor.

   It usually takes around 1min for the system
to boot up. When ready you will hire the GO
sound.
  When you power the system on the buttons
go over the programmed sequence and light
up RGB for a brief moment when the power is
provided by the computer.		   At this time the game is set for the first test.
  After the first sequence the buttons go dim and
are awaiting the game to start.		   Press start on the monitor and check that the
buttons are in the right positions by playing
one game.
 

In play safety guidelines

Before beginning any exercise program, it is recommended that you consult with your doctor.
Children under the age of 8 must always be supervised by an adult when using the equipment.
Visually check the equipment before using it, for any signs of damage, component failure or loose cables that could become a tripping hazard.
Wear appropriate clothing. Anti slip socks must be worn while using the equipment.
Remove all items from your pockets prior to participation.
Practice being in control of your bounce before using the equipment. Be aware of how to bend
your knees to control or stop your bounce. Always stay in control. Uncontrolled jumps or falls are
likely to result in injuries to yourself and others.
Don’t drink or eat while playing the game.

Maintenance

  • The device is easily damaged if you put excessive pressure on the display or other components.
  • If not in use for a long period of time please disconnect the device from power.
  • Disconnect the device when cleaning with a slight damp cloth. The display and buttons may be cleaned with slightly damp cloth, but do not use any organic solvents to clean the device.

 

RFID Functionality

Visi Timer supports RFID technology for a seamless, touch-free gaming experience. If your park uses RFID bracelets, players can simply tap their bracelet near the button to activate it—no pressing required. The RFID reader inside the button will detect the bracelet and trigger the game action automatically.

This functionality adds convenience, hygiene, and speed to the game, making it especially suitable for high-traffic venues and younger players.

Important:

  • Make sure the RFID bracelets are properly registered with your park’s system.

  • Players should hold the bracelet close to the center of the button until they see a visual confirmation (e.g., light or sound) indicating successful activation.

  • If an RFID bracelet is not recognized, check its registration or try using a different bracelet.

Game objective

The game objective is for the player to get the fastest time across the obstacle course. The time is shown on the main display for all players. The game offers simultaneous game for a maximum of 3 people. Player with the best time wins.

 

Troubleshooting

The system doesn’t power on:

  • Check the power connection on the computer and AC-DC Power supply.
  • Check the display power and HDMI connection

One or more of the buttons aren’t responding:

  • Check the last two digits on the computer’s serial code and compare them to the labels on the buttons. If they are not matching the game system will not work.

One or more buttons don’t light up:

  • Check the connection from the button to the aggregator box and the connection to the computer.

  • If the connections are ok and the button is not responding please contact us at: support@visiorgames.com

​On one or more buttons is not responding:

  • Restart the system and wait for the startup cycle. Check the button again.
  • If the lights in the button are not light up Please contact us at: support@visiorgames.com.

There is no picture on the display:

  • Check the display power cable.
  • Check the HDMI connection from the PC to the display.
  • If you just started the game please wait for 1 minute and check again.

The button is not starting the timer when hit:

  • Check the connection to the aggregator box and computer.
  • If the button lights up but with no response please contact us at: support@visiorgames.com.