Important Safety Instructions

CAUTION! OPENING THE DEVICE MIGHT RESULT IN ELECTRICAL SHOCK

	Visually check the product for any signs of damage, component failure and/or missing parts.		Do not distract others while they are installing the product.
	Any changes or modifications to the devices hardware or software will void the warranty of the device and may cause the device not to work properly.		The trampoline and its surroundings must always comply with local standards for trampolines.   If the instructions contradict the local regulations please disregard them.
	Keep the device away from any contact with water. Warranty void after water damage.		For indoor and outdoor use.
	Keep the device away from fire. Warranty void after fire damage.		Installation should be performed by authorized personnel.
	Be sure to take all anti-static precautions.		Optimum operating temperature is from 5°C to 30°C. Avoid extreme fluctuations of temperature.
	Wear appropriate clothing: Do not wear loose clothing or jewellery.		These instructions apply to the device itself. Please read the manual before operation.
	Long hair should be tied back.		Always use designated buttons on the designated system. and/or missing parts.
	Tidy back any loose cables that could become a tripping hazard.		Immediately inform Visior games for maintenance advice if you have concerns.

 

What’s in the box?

Full setup

First time setup

A typical installation should take 2 people around 45 minutes.

	Ensure there is nobody on the trampoline when installing the device.		Make sure that the buttons are correctly oriented and clear of any obstructions.
	Provide 230V 5A for the device.		The buttons are pre assigned to only one computer that came with the game set, you can’t switch them with other systems. And they are also assigned to the correct side.
	Provide internet connection point. All of the Visior Games products need to connect to the internet. If you own more than one device, provide internet access to the device in the center of the park and connect the devices via router or hub provided by us.		The labels on the buttons define a number that is correlated to the correct computer’s serial code.
			Make sure the electrical power is off during installation.

Installation of the game

Mounting buttons

Decide on the position of the buttons. The depth of the wall should be 2-7 centimeters. Drill three holes for each button, two for the screws (1cm) and one for the data cable (2cm). Insert the button as shown:

 

After you have inserted the buttons, connect the cables to aggregators and to the computer.

Also connect the computer to the screen with HDMI and provide ethernet internet and lastly, power.

Installation checklist

CHECK 1 Pre-power up checkups

• Mounted onto a wall designed for the game.
• All buttons are connected to separate aggregator boxes.
• There are two cables connected from aggregator boxes to the computer and connectors tighten.
• Make sure the ethernet cable with internet access is connected to the computer.
• Make sure the display is connected with HDMI and USB cables.
• All fixings are tight and secure.
• No signs of damage, component failure and/or missing parts.
• No trapped and/or pinched cables.
• No loose cables that could become a tripping hazard.
• Make sure there is no strain on the cables and the connectors.
• All electrical components are away from contact with water and heat sources.

CHECK 2 Power up

• All buttons light up for a brief moment.
• The display is turning on.
• Game start screen appears on the display after around 1 minute.
• Go! sound is heard at startup.
• All buttons are dim before the start of the game.

CHECK 3 Press start on display

• The clock starts the countdown on the display.
• The buttons light at the right side when starting the game.
• All buttons flash when hit.
• Sounds can be heard when the buttons are hit.
• The hits are registered on the display.
• Sounds are heard after the correct hit.

CHECK 4 Ready for use

• Play area is clear.

Powering on for the first time

1. Make sure that all cables are connected to the aggregator boxes and the computer and connectors tightened.
2. Make sure that the buttons are on the correct side of the cube relative to the monitor.
3. When you power the system on the buttons go over the programmed sequence and light up RGB for a brief moment when the power is provided by the computer.
4. After the first sequence the buttons go dim and are awaiting the game to start.
5. Monitor must power on by itself when connected to power.
6. It usually takes around 1min for the system to boot up. When ready you will hire the GO sound.
7. At this time the game is set for the first test.
8. Press start on the monitor and check that the buttons are in the right positions by playing one game.

In play safety guidelines

	Before beginning any exercise program, it is recommended that you consult with your doctor.
	Children under the age of 8 must always be supervised by an adult when using the equipment.
	Visually check the equipment before using it, for any signs of damage, component failure or loose cables that could become a tripping hazard.
	Wear appropriate clothing. Anti slip socks must be worn while using the equipment.
	Remove all items from your pockets prior to participation.
	Practice being in control of your bounce before using the equipment. Be aware of how to bend your knees to control or stop your bounce. Always stay in control. Uncontrolled jumps or falls are likely to result in injuries to yourself and others.
	Don’t drink or eat while playing the game.

Maintenance

• The device can be damaged if you put excessive pressure on the display or other components.
• If not in use for a long period of time please disconnect the device from power.
• Disconnect the device when cleaning with a slight damp cloth. The display and buttons may be cleaned
  with slightly damp cloth, but do not use any organic solvents to clean the device.
• Check that all screws are tightened and buttons are physically well mounted

Game objective

Troubleshooting

The system doesn’t power on:

• Check the power connection to the system.
• Check the display power and HDMI connection.

The game won’t start, screen doesn’t work:

• Check the HDMI connection from the computer to the screen.
• The display must be turned on in order for screen to work.

One or more of the buttons are not assigned to the right side of the game:

• Check the markings on the buttons and ensure they are correctly inserted.

One or more buttons don’t light up:

• Check if the system is turned on.
• Check the connection from the button to the aggregator box and the connection to
the computer.
• If the connections are ok please contact us at support@visiorgames.com.

On one or more buttons the green light is on when no contact is made with the button:

• Restart the system and wait for the startup cycle. Check the button again.
• If the lights in the button are constantly green please contact us at:
support@visiorgames.com

There is no picture on the display:

• Check the display power cable.
• Check if the system is turned on.
• Check the HDMI connection from the PC to the display.
• If everything seems in order but no picture is displayed please contact us at
support@visiorgames.com.