Important Safety Instructions

CAUTION! OPENING THE DEVICE MIGHT RESULT IN ELECTRICAL SHOCK

	Visually check the product for any signs of damage, component failure and/or missing parts.		Do not distract others while they are installing the product.
	Any changes or modifications to the devices hardware or software will void the warranty of the device and may cause the device not to work properly.		The trampoline and its surroundings must always comply with local standards for trampolines.   If the instructions contradict the local regulations please disregard them.
	Keep the device away from any contact with water. Warranty void after water damage.		For indoor use only.
	Keep the device away from fire. Warranty void after fire damage.		Installation should be performed by authorized personnel.
	Be sure to take all anti-static precautions.		Optimum operating temperature is from 5°C to 30°C. Avoid extreme fluctuations of temperature.
	Wear appropriate clothing: Do not wear loose clothing or jewellery.		These instructions apply to the device itself. Please read the manual before operation.
	Long hair should be tied back.		Always use designated buttons on the designated system. and/or missing parts.
	Tidy back any loose cables that could become a tripping hazard.		Immediately inform Visior games for maintenance advice if you have concerns.

 

What’s in the box?

Full setup

First time setup

A typical installation should take 2 people around 90 minutes.

	Ensure there is nobody on the trampoline when installing the device.		The buttons and targets are pre assigned to only one computer that came with the game set, you can’t switch them with other systems. And they are also assigned to the correct side.
	Make sure that the targets are on the correct side they are marked on the back side.		Follow the labels on the dodge targets for correct installation (L is left, R is right 1-4 is the position, 1 is closest to the monitors)
	Make sure that the buttons and targets are correctly oriented and clear of any obstructions.		Make sure the electrical power is off during installation

 

Installation checklist

CHECK 1 Pre-power up checkups

• Mounted onto a construction designed for the game and in the right positions.
• All buttons and targets are connected to the correct aggregator boxes.
• Tighten all the connectors, the can bus cables and target cables.
• Make sure the ethernet cable and DC power is connected to the computer.
• Make sure the display is connected with HDMI and power cables.
• All fixings are tight and secure.
• No signs of damage, component failure and/or missing parts.
• No trapped and/or pinched cables.
• No loose cables that could become a tripping hazard.
• Make sure there is no strain on the cables and the connectors.
• All electrical components are away from contact with water and heat sources.

CHECK 2 Power up

• All targets light up for a brief moment.
• The display is turning on. 
• Game start screen appears on the display after around 1 minute.
• Go! sound is heard at startup.
• All targets are dim before the start of the game.
• The start button lights up.

CHECK 3 Final check

• The clock starts the countdown on the display.
• All targets flash when hit.
• Sounds can be heard when the targets are hit.
• The score is registered on the display.
• Hit every target and check if the score is added to the correct side. 

CHECK 4 Ready for use

• Play area is clear.

 

Powering on for the first time

	Make sure that all cables are connected to the aggregator boxes and the computer and connectors tightened.		Monitor must power on by itself when connected to power.
	Make sure that the targets are on the correct side of court relative to the monitor.		It usually takes around 1min for the system to boot up. When ready you will hire the GO sound.
	When you power the system on the buttons go over the programmed sequence and light up RGB for a brief moment when the power is provided by the computer.		At this time the game is set for the first test.
	After the first sequence the buttons go dim and are awaiting the game to start.		Press start on the monitor and check that the buttons are in the right positions by playing one game.

In play safety guidelines

	Before beginning any exercise program, it is recommended that you consult with your doctor.
	Children under the age of 8 must always be supervised by an adult when using the equipment.
	Visually check the equipment before using it, for any signs of damage, component failure or loose cables that could become a tripping hazard.
	Wear appropriate clothing. Anti slip socks must be worn while using the equipment.
	Remove all items from your pockets prior to participation.
	Practice being in control of your bounce before using the equipment. Be aware of how to bend your knees to control or stop your bounce. Always stay in control. Uncontrolled jumps or falls are likely to result in injuries to yourself and others.
	Don’t drink or eat while playing the game.

Maintenance

• The device can be damaged if you put excessive pressure on the display or other components.
• If not in use for a long period of time please disconnect the device from power.
• Disconnect the device when cleaning with a slight damp cloth. The display and buttons may be cleaned
  with slightly damp cloth, but do not use any organic solvents to clean the device.

Game objective

Troubleshooting

The system doesn’t power on:

• Check the power connection to the system.
• Check the display power and HDMI connection.

The game won’t start, screen doesn’t work:

• Check the HDMI connection from the computer to the screen.
• The display must be turned on in order for screen to work.

One or more of the targets are not assigned to the right side of the game:

• Check the labels on the targets, one or more targets must be in a wrong position.
• Check the L and R markings on the targets.

One or more targets doesn’t light up:

• Check if the system is turned on.
•  Check the connection from the target to the aggregator box and the connection to the computer. DO NOT PLUG OR UNPLUG CAN BUS CABLES WHEN THE SYSTEM IS TURNED ON!
• If the connections are ok please contact us at: support@visiorgames.com

The start button does not start the game:

• Check the CANBUS cable connection.
• If everything seems in order contact us at: support@visiorgames.com

There is no picture on the display:

• Check the display power cable.
• Check if the system is turned on.
• Check the HDMI connection from the PC to the display.
• If everything seems in order but no picture is displayed please contact us at support@visiorgames.com.